Herbistry420
Smoke / Vape / Blaze

DynaVap OMini Review: How to Draw, Heat and Run It With Cap Armor

My DynaVap OMini review: what the titanium unibody is, who it's for, how to draw on it, the IH 3.0 settings I used at 40 and 50 watts, insert height to avoid combustion, and why Cap Armor and a J-hook make it better.

by Fordee

The OMini is tiny, and that's the first thing everybody notices. It's also the whole reason it hits the way it does. Get the heat and the draw right and the results are really impressive. Rip on it without thinking and the bowl dies on you.

What the OMini is

It's a unibody, so the tip and the stem are one piece of titanium and you can't separate them. The part that does come out is the mouthpiece, with the condenser attached to it. Grip the mouthpiece and pull, and you've got two pieces: the condenser and mouthpiece, and the unibody.

Marketing hype, or can you feel it?

Honestly, I thought it was hype when I first got it. Heat slits, thermal brakes, recycled air. It sounded like a garbage man calling himself a sanitation engineer. (No shade to garbage men, they make bank and I'm jealous most of the time.)

Then I hit it correctly for the first time, and you can feel it. There's air moving around in there while you draw. I don't know how else to describe it, but something is clearly happening.

Who it's for

The tinkerer. If you like to mess with your gear and experiment, you'll have fun with this. You're going to have to experiment to get the good results, and if that sounds like more of a pain in the ass than it's worth, this one might not be for you.

The reason is the short air path. A short vape makes you think about heat and draw more. The upside is that the vapor has less time to condense on the way to your mouth, so I feel like you catch more of the volatile low-end terpenes along with everything else. To me that's a fuller-spectrum, more nuanced high, and it's my favorite thing about the OMini.

How to draw on it

This is where most of the learning curve is. Draw too slow and the recycler isn't doing its work. Rip on it like a bong and you pull so much heat out of the tip and cap that the bowl dies on you. You want a steady rate in between, and when you hit it, you'll feel the air moving.

Two draw styles worth trying:

  • Slow and sustained, one long even pull.
  • Stop and start: draw, stop, give the tip a second to recover, then go again.

Both change how much heat stays in the tip and cap, so play with them and see what you like.

IH 3.0 settings I used

Beginner mode, a mid-temp sesh:

  • IH 3.0 set to 40 watts.
  • Insert flush.
  • About 21 seconds at roughly half battery. It didn't click in that time, and a little pre-vapor is normal.

I run it at 40 watts for consistency. At max power the timing changes as the batteries drain, so the fifth bowl behaves differently from the first. The IH 3.0 can still put out 40 watts on low batteries, so every session behaves the same.

Advanced mode, a high-temp sesh:

  • Cap Armor on.
  • Max power output set to 50 watts.
  • Insert flush.
  • Around 41 to 42 seconds.

If you want more starting points for the heater, here are my IH 3.0 DynaVap settings.

Insert height and combustion

Changing the height of the insert changes where the heat goes. Raise it and you're aiming the heat at the very end of the tip, which gives you a lower-temp session. Drop it down and you heat higher up the tip, which gives a deeper heat soak and more chance of combustion.

If you're combusting, either shorten your timing or raise the insert. Just remember that if you're running max power, your timing also shifts with the battery level.

Cap Armor and the J-hook

Cap Armor adds thermal mass, so more energy goes into the herb on that first extraction. The extractions are a bit bigger and it takes the high a little further. I ran it through my J-hook from High Artisan, which is super nice with this. I put the same Cap Armor and J-hook combo on the Vong-X Stealth here.

It gets hot

It's titanium, so it heats up fast and gives the heat back fast. I think that's exactly why they picked it for a vape this short. In stainless steel you'd be waiting way too long to get back to temp. The catch is that a short titanium vape gets hot in your hand. Two sessions back to back handheld, you can do it. Three, I didn't even try. That's why you'll probably prefer it in a J-hook, and in a J-hook this thing is wild.

Seven or eight takes later

This video did not go as planned. The batteries died, then the GoPro overheated, and I went through way more bowls than I meant to. By the end I was pretty blasted, which you'll see. Still a fun device.

What's your draw style on a DynaVap? Tell me in the comments on the video.

Frequently Asked Questions

Can you take the DynaVap OMini apart?
Partly. The tip and stem are one titanium unibody and don't separate. The mouthpiece pulls out with the condenser attached to it.
What IH 3.0 settings work for the DynaVap OMini?
I ran it at 40 watts with the insert flush, about 21 seconds at roughly half battery. With Cap Armor I set max power to 50 watts, insert flush, around 41 to 42 seconds. I use a fixed wattage so the timing stays the same as the batteries drain.
How should you draw on the DynaVap OMini?
Not too slow and not too hard. Too slow and the recycler doesn't do its work, too hard and you pull the heat out of the tip and cap. A slow sustained pull or a stop-and-start draw that lets the tip recover both work.
Does the DynaVap OMini get hot?
Yes. It's short and it's titanium, so it heats and cools fast. Two sessions back to back handheld is doable. A J-hook helps a lot.
Is Cap Armor worth it on the OMini?
For me, yes. It adds thermal mass, so the extractions are a bit bigger and the high goes a little further. In this video it took around 41 to 42 seconds at 50 watts.

Where to Buy

Some links above are affiliate links. We may earn a commission at no extra cost to you.

From the Shop

See all
Share